MR-J3-40B(GA) MRJ340B(GA) MITSUBISHI Servo Driver 400W 3Ph 2.8A. 1D
| Brand/Manufacturer | MITSUBISHI / JAPAN |
| Part Number | MR-J3-40B(GA) |
| Alternate Part Number | MR-J3-40B(GA) |
| Description | Servo Driver |
| Dimennsions | 6.4cm x 11.0cm x 20.4 cm |
| Weight | 1.3kg |
Product Details
ALM turns off when power is switched off or the protective circuit
isactivated to shut off the base circuit.Without alarm occurring,
ALM turns on within about 1s after power-on.
Electromagnetic brake interlock: When using this signal, set
operation delay time of the electromagnetic brake in parameter
No.PC02.In the servo-off or alarm status, MBR turns off.
INP turns on when the number of droop pulses is in the preset
in-position range. The in-position range can be changed using
parameter No. PA10.When the in-position range is increased, INP may
be on conductive status during low-speed rotation.INP turns on when
servo on turns on.This signal cannot be used in the speed loop
mode.
When using the signal, make it usable by the setting of parameter
No.PD07 to PD09.RD turns on when the servo is switched on and the
servo amplifier is ready to operate
Speed reached: When using this signal, make it usable by the
setting of parameterNo.PD07 to PD09.When the servo is off, SA will
be turned OFF. When servo motor rotationspeed becomes approximately
setting speed, SA will be turned ON.When the preset speed is
20r/min or less, SA always turns on. This signal cannot be used in
position loop mode.
Moore News
POWER INDUSTRY
Hydropower industry with power industry capabilities.
The working power of the remote I/O is provided by the
corresponding LCU to the unit local control unit (LCU1, LCU2, LCU3,
LCU4).
The LCU should provide an RS-485 serial interface, using the Modbus
(Master and Slave) standard communication protocol interface.
Molex is used for gateway protocol conversion. The module is
directly plugged into AB's 1756 rack and has standard blocks for
programming.
The international standard industrial Ethernet protocol EtherNet/IP
is used between the PLC and the workstation in the LCU.
The communication speed reaches 100Mbps, and the PLC adopts AB
ControlLogix system governor oil pump control loop and ball valve
control loop to enter the unit's local LCU control.
More Products
| EPRO | PR6423/015-030 CON021 | SIEMENS | 6NG4207-8PS02 |
| EPRO | PR9268/302-000 | SIEMENS | 39ACM28AEN 16139-218/3 |
| EPRO | PR6423/00R-010 | SIEMENS | 6DP1616-8CA |
| EPRO | PR6423/002-030 | SIEMENS | 6DP1360-8BA |
| EPRO | PR6423/010-000-CN CON021 | SIEMENS | 6DP1661-8AA |
| EPRO | PR6423/004-120-CN CON021 | WOODWARD | 5464-544 |
| TRICONEX | 2551 | WOODWARD | 5464-211 |
| TRICONEX | 2658 | WOODWARD | 5417-175 |
| TRICONEX | 3502E | WOODWARD | 5453-203 |
| TRICONEX | 3601E | WOODWARD | 5441-693 |
| TRICONEX | 2700 2700-2 | WOODWARD | 5464-210 |
Contact Us
miya@mvme.cn(Click)
Email: miya@mvme.cn
QQ: 2851195450
Tel: 86-18020776792
Skype: miyazheng52
