Allen Bradley 1442-PS-0860E0005A 1442PS0860E0005A AB 1442 PS 0860E0005A

Product Description:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground

conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation

chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive

devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

Contact Information:

Contact:Miya ( manager)

Email :sales@mooreplc.com
Q Q: 2851195450
Skype: miyazheng520
Mobile:86-18020776792 ( what's app )

Related Product Recommendation:

The Remote I/O communications module allows a SCANport product to look and act like a Remote I/O chassis when connected to a programmable controller. Data contained in the input/output image table is transferred between the programmable controller by the Remote I/O scanner, the same as with any

Remote I/O chassis. You control the location of data transferred by setting the rack address and
starting group. You control the amount of data by setting the DIP switches on SW3. Important: Thecommunications module does not scale the data that is transferred. Consequently, all scaling of the

data must be done in the controller. Refer to the user manual for your SCANport product for details on
device units. Important: The Remote I/O to SCANport conversion is asynchronous. Data sent to the adapter for transfer to the drive must be maintained until the drive has received data.DIP switches on

SW3 determine how the data contained in the programmable controller I/O image table is used in the drive. Figure shows an I/O image table.

1746-A2 2-Slot Expansion Rack AB
1746-A4 4-Slot Chassis AB
1746-A7 7-Slot Chassis AB
1746-BAS BASIC Language Module AB
1746-BAS-T BASIC Language Module - High Speed AB
1746-BLM Blow Molding Module AB
1746-BTM Barrel Temperature Module AB
1746-C16 Chassis Interconnect Cable AB
1746-C9 Chassis Interconnect Cable AB
1746-FIO4I Fast Analog Input/Output Module AB
1746-FIO4V Fast Analog Input/Output Module AB
1746-HS Motion Controller Module AB
1746-HSCE High Speed Counter Module AB
1746-HSCE2 Multi-Channel High Speed Counter Module AB
1746-HSRV Servo Control Module AB
1746-HSTP1 Stepper Control Module AB
1746-HT Termination Panel AB
1746-IA16 120V AC Input Module AB
1746-IA4 120V AC Input Module AB
1746-IA8 120V AC Input Module AB
1746-IB16 Current Sinking DC Input Module AB
1746-IB32 Current Sinking DC Input Module AB
1746-IB8 Current Sinking DC Input Module AB
1746-IC16 Current Sinking DC Input Module AB
1746-IG16 Current Sourcing TTL Input Module AB
1746-IH16 Current Sinking DC Input Module AB

1746-IM16 240V AC Input Module AB
1746-IM4 240V AC Input Module AB
1746-IM8 240V AC Input Module AB
1746-IN16 24V AC/DC Input Module AB

APPLIED MATERIALS P/N 1220-0025 BAR IONIZER 7-EMITTERS 28.4"LONG 28VAC ADAPTER

APPLIED MATERIALS P/N 1350-01200 BARATRON PRESSURE TRANSMITTER

APPLIED MATERIALS P/N 3700-01245 O-RING id .364 CSD .070 VITON 75 DURO BLK

APPLIED MATERIALS P/N 3700-01131 O-RING id 2,175 CSD .130 VITON 75 DURO B

APPLIED MATERIALS P/N 3700-02887 O-RING id 489CSD .070 POLYURETHANE

APPLIED MATERIALS P/N 3700-01208 REV.0 O-RING id 12.984 CSD

APPLIED MATERIALS 0680-00400 SERVICE TOOLS LOTO DEVICE FOR SUPPLEMENTAL CIRCUI

APPLIED MATERIALS P/N 3060-00275 BALL BEARING 12MM BORE X 28MM OD X 8MM W/ VIT

APPLIED MATERIALS P/N 0720-01566

APPLIED MATERIALS P/N 0150-95943 TRANSZORB ASSY (ION SOuRCE)

APPLIED MATERIALS P/N 3950-01029 SPRAY NOZZLE HH-TYPE 1/8 MNPT .040 KYNAR

APPLIED MATERIALS P/N 3880-01129 POLISHER

APPLIED MATERIALS P/N 1313-76400 TOP PLATE BRACKET

WELCH ALLYN P/N M50E021 SOLARC MINIATURE METAL HALIDE ARC LAMP

INTEL PRO/1000 PT DUAL PORT SERVER ADAPTER EXP19402PT **NEW**

CISCO Smart Serial Crossover Cable, 10' (ref.p/n # CAB-SS-2626X-10) **NEW**

MITSUBISHI 4 CHANNEL ANALOG INPUT MODULE FX2NC-64MT...

HP 447047-B21 1/10GB-F VIRTUAL CONNECT ETHERNET MODULE NEW-OTHER

VEXTA NANOSTEP/ BY ORIENTAL MOTOR CO. 5 PHASE DRIVER MODEL DFR1514A

The use of the product:

1.the elevator industry,

Moore Automation is a company specializing in the sales of modules and spare parts for world-renowned brands (DCs systems, robot systems, large servo control systems). The company's products include: distributed control systems (DCS), programmable controllers (PLC), MOTOROLA -MVME industrial modules, industrial control communication converters (Anybus), remote output/input modules (RTU), industrial computers (PC), industrial low-frequency screens (IPC), human-machine interface SCSI (50, 68, 80Pin ) AnyBus(Gateway)o The spare parts we sell provide one-year quality guarantee and have undergone strict testing and certification. Now we have become a global sales enterprise of industrial automation spare parts and components.