Allen Bradley Modules 1794-TB3G 1794 TB3G PLC Terminal Base Unit New

Product Description:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation
chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

Related Product Recommendation:

Product's Character:

Two serial connectors to simplify RS-485 multi-dropping and host communications Several analog or digital command interfaces: Indexing (absolute with the Homing feature, incremental, or
registration)10 Volt analog interface—position, velocity, or torque control Presets (from one to eight binary inputs)—torque or velocity control Quadrature encoder digital interface—electronic gearing position follower Step/Direction digital interface—position control CW/CCW (step up/step down) interfaceposition control Operating mode override—alternate movement interface Host command digital interface The ULTRA 100/200 drives host command protocol provides optional drive configuration using the drive serial communications interface. This powerful feature allows your controller to access all of the drive digital controls using sequences of ASCII characters. The protocol includes error checking to
ensure the integrity of the transmitted commands. In installations that have multiple axes, up to 32 ULTRA 100/200 drives can be addressed by a host computer. These drives communicate with the host
computer using a four-wire RS-485 serial interface. The host command protocol includes specific drive addressing, which allows the host to communicate with all the connected drives concurrently.

1756-L55M12/A 1756-L55/A, 1756-M12/A Logix5555 Processor, 750KB memory, Series A AB
1756-L55M13/A 1756-L55/A, 1756-M13/A Logix5555 Processor, 1.5 MB memory, Series A AB
1756-L55M14/A 1756-L55/A, 1756-M14/A Logix5555 Processor, 3.5 MB memory, Series A AB
1756-L55M16/A 1756-L55/A, 1756-M14/A Logix5555 Processor, 7.5 MB memory, Series A AB
1756-L61/A Logix5561 Logix5561 Processor - 2MB AB
1756-L61/B Logix5561 Logix5561 Processor - 2MB AB
1756-L62/A Logix5562 Logix5562 Processor - 4MB Memory AB
1756-L62/B Logix5562 Logix5562 Processor - 4MB Memory AB
1756-OB16E/A Digital Fused Output Module - Series A AB
1756-PA72/A 1756-PA72 Power Supply - Series A AB
1756-PA72/B 1756-PA72 Power Supply - Series B AB
1756-PA72/C 1756-PA72 Power Supply - Series A AB
1761-CBL-PM02 Program Storage Device Cable AB
1761-L32BBB MicroLogix 1000 Unit AB
1762-IQ16 16PT 24VDC Power Supply Module AB
1762-MM1 MicroLogix Memory Module AB
1762-MM1RTC MicroLogix Memory and Real-Time Clock Module AB
1762-OF4 Analog Output Module AB
1762-OW16 16PT VAC/VDC Relay Output AB
1762-RTC MicroLogix Real-Time Clock Module AB
1764-24BWA MicroLogix 1500 Base Unit AB
1764-LRP Processor AB
1764-LSP Processor Module AB
1766-L32BWA Micro Logic Relay Output AC Power AB
1769-ECR Right End Cap AB
1769-IF4 Analog Input Module AB
1769-IQ16 Digital Input Module AB

John Crane ProTech LSE-3250-4500-1 labyrinth seal 3.25" x 4.50"

John Crane 2.0" mechanical seal 832147-016 Type 8b-2BL B184-82 H88543

FlowServe cartridge seal P-50 P50 1.575" inch 40mm 409892 flexible stator pusher

FlowServe cartridge seal P-50 P50 1.575" inch 40mm 409892 flexible stator pusher

Chesterton 155-13 Seal Cartridge #687567 seal size -13 shaft size 1.625"
FlowServe split mechanical seal ring 7.50" inch K43S7500PC3 PCIII

John Crane 3.25" Stationary Seat T1- TC 1154137 Tungsten
Chesterton 442 Geminl Split Seal Spare Seal kit -14 shaft 1.750" item#682269

John Crane 3.25" rotary seat TC 1154129 37-E-5B

Gland for L-8 Moyno Pump 2.125" part # 680ABT-SGF-215-34 Gould Pump Company

Chesterton 155 Seal Repair Kit #RK155214-1 size -18 shaft size 2.250" 1366574

Chesterton 3.25" x 4.75" repair parts RBA 3.250x4.750x1.00 Item # 059796 59796

Flowserve 2.0" Cartridge dual bellows Mechanical Seal X-200 127353 HASTELLOY C

Spiraltrac FI3125RS4149(ESC) new split reducing flush bushing 3.125"

FlowServe split mechanical seal 7.50" DMC A23C7500P33 P79654 99

FlowServe RK407803PS2 repair kit split mechanical seal 7.25" SGL PSSIIER2EFVV

Durametallic MFB27012341 GF Duraflon Flow reducing split bushing 3.75" 12x14-18S

Durametallic lip seal GF duraflon QF3A2125AB3 2.125" DMC F3A2125AB

FlowServe flow restriction GF Duarflon Bush bushing AF3A6690A33 -0 JS 233078 NEW

Chesterton 221 split seal repair kit 221-14 SPK CB/SC EP 1.750" size -14 047136

SKF 48768 Oil Seal NEW Grease Seal CR-48768 Seal

John Crane 2.75" mechanical seal 1410224 Type 2 FSD-3020

The use of the product:

Moore Automation is a company specializing in the sales of modules and spare parts for world-renowned brands (DCs systems, robot systems, large servo control systems). The company's products include: distributed control systems (DCS), programmable controllers (PLC), MOTOROLA -MVME industrial modules, industrial control communication converters (Anybus), remote output/input modules (RTU), industrial computers (PC), industrial low-frequency screens (IPC), human-machine interface SCSI (50, 68, 80Pin ) AnyBus(Gateway)o The spare parts we sell provide one-year quality guarantee and have undergone strict testing and certification. Now we have become a global sales enterprise of industrial automation spare parts and components.