Allen Bradley Modules 1785-L60B 1785 L60B AB 1785L60B Processor

Product Description:

The Remote I/O communications module allows a SCANport product to look and act like a Remote I/O chassis when connected to a programmable controller. Data contained in the input/output image table is transferred between the programmable controller by the Remote I/O scanner, the same as with any Remote I/O chassis. You control the location of data transferred by setting the rack address and
starting group. You control the amount of data by setting the DIP switches on SW3. Important: Thecommunications module does not scale the data that is transferred. Consequently, all scaling of the data must be done in the controller. Refer to the user manual for your SCANport product for details on
device units. Important: The Remote I/O to SCANport conversion is asynchronous. Data sent to the adapter for transfer to the drive must be maintained until the drive has received data.DIP switches on SW3 determine how the data contained in the programmable controller I/O image table is used in the drive. Figure shows an I/O image table.

Related Product Recommendation:

Product's Character:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

1771-OFE2 Analog Output Module AB
1771-OFE3 Analog Output Module AB
1771-OG TTL Output Module AB
1771-OGD TTL Output Module AB
1771-OM Digital Output Module AB
1771-OMD AC Output Module AB
1771-ON Digital Output Module AB
1771-OP Digital Output Module AB
1771-OQ Digital Output Module AB
1771-OQ16 1771-OQ16 A Digital Output Module AB
1771-OR Digital Output Module AB
1771-OVN Digital Output Module AB
1771-OW Selectable Contact Module AB
1771-OW16 1771-0W16 B Digital Output Module AB
1771-OWN 1771-0W16 B Digital Output Module AB
1771-OWNA 1771-0W16 B Digital Output Module AB
1771-OX Output Module AB
1771-OYL Digital Output Module AB
1771-OZC Contact Output Module AB
1771-OZL Digital Output Module AB
1771-P10 Power Supply Module AB
1771-P2 Auxiliary Power Supply AB
1771-NIVR Analog Input Module AB
1771-NIVT Analog Input Module AB
1771-NOC Analog Output Module AB
1771-NOV Analog Output Module AB
1771-NOV A High Resolution Isolated Analog Module AB
1771-NR Analog Input Module AB
1771-NT1 Analog Input Module AB
1771-NT2 Analog Input Module AB
1771-OA Digital Output Module AB
1771-OAD AC Output Module AB
1771-OAN Digital Output Module AB
1771-OBD Digital Output Module AB

1771-OBN Digital Output Module AB
1771-OC Digital Output Module AB
1771-OD Digital Output Module AB
1771-OD16 Digital Output Module AB
1771-ODC Digital Output Module AB
1771-ODD Digital Output Module AB
1771-ODZ Digital Output Module AB
1771-OFE1 960578 Analog Output Module AB

Anorad DR-300 X Y R Axis Controller AMAT SemVision cX missing Y R Axis PCB used

ICT 4916171 PMT+PRE AMP In-Lens Detector AMAT 50409150000 SemVision cX works

VAT 26324-KA41-0001 HV Angle Valve AMAT SemVision cX used working

A to Z Electronics 50419600200 OMC PCB Chassis AMAT SemVision cX working

A to Z Electronics 50312460100 ETPS Assy AMAT SemVision cX used working

Pneutal SCP-161 10 bar Vacuum Tank AMAT Semvision cX used working

AMAT 0090-A2230 IPU Assy Industrial Computer 0090-A0970 SemVision cX used works

Thermo Electron 8815A-3SUS-SN EDX Sensor AMAT SemVision cX used working

RH Electronics 50419700200 OM Power Supply Cage OMP AMAT SemVision cX used works

CMC AM422670P000 Motion Controller Aximate/C AMAT SEMVision cX used working

Lambda 40935 Power Supply Alpha 400W AMAT SemVision cX working

Varian 9699504S011 Pump Controller & Cables Turbo-V 250 C.U. SemVision cX works

AMAT SemVision Wafer Transfer Arm Assembly AMAT SemVision cX 300mm works 800-494

MKS 41A12DGA2BA010 10 TORR-G Trip Baratron Pressure Switch 100 TORR-G used works

Brooks 6-0001-0817-SP Robot Rail LTRA 042-SBI AMAT SemVision cX working

AMAT SemVision cX SEM Tilt Motor Assembly used working

Opal ETD Board 50312575100 Circuit Board AMAT SemVision cX working

Opal DVD Board 50312540200 Circuit Board AMAT SemVision cX working

The use of the product:

Moore Automation is a company specializing in the sales of modules and spare parts for world-renowned brands (DCs systems, robot systems, large servo control systems). The company's products include: distributed control systems (DCS), programmable controllers (PLC), MOTOROLA -MVME industrial modules, industrial control communication converters (Anybus), remote output/input modules (RTU), industrial computers (PC), industrial low-frequency screens (IPC), human-machine interface SCSI (50, 68, 80Pin ) AnyBus(Gateway)o The spare parts we sell provide one-year quality guarantee and have undergone strict testing and certification. Now we have become a global sales enterprise of industrial automation spare parts and components.