Allen Bradley Modules 1771-IR 1771 IR AB 1771IR Input Module 12 month warranty automobile manufacturing

Product Description:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

Related Product Recommendation:

Product's Character:

The Remote I/O communications module allows a SCANport product to look and act like a Remote I/O chassis when connected to a programmable controller. Data contained in the input/output image table is transferred between the programmable controller by the Remote I/O scanner, the same as with any Remote I/O chassis. You control the location of data transferred by setting the rack address and
starting group. You control the amount of data by setting the DIP switches on SW3. Important: Thecommunications module does not scale the data that is transferred. Consequently, all scaling of the data must be done in the controller. Refer to the user manual for your SCANport product for details on
device units. Important: The Remote I/O to SCANport conversion is asynchronous. Data sent to the adapter for transfer to the drive must be maintained until the drive has received data.DIP switches on SW3 determine how the data contained in the programmable controller I/O image table is used in the drive. Figure shows an I/O image table.

1769-OB16 Digital Output Module AB
1769-OF2 Analog Current/ Voltage Output AB
1770-P1 Power Supply AB
1770-SC Station Connector AB
1770XYC AB PLC 5 Battery AB
1771-0B Digital Output Module AB
1771-A2B Allen Bradley Racks AB
1771-A3B 12 Slot I/O Chassis AB
1771-A4B 16 Slot I/O Chassis AB
1771-AD I/O Chassis - 16 Slot AB
1771-AL PLC 2 I/O Adaptor Module AB
1771-ALX PLC5 Local I/O Adapter Module AB
1771-ASB Remote I/O Adapter Module AB
1771-ASC Remote I/O Adapter Module AB
1771-CE Power Supply Cable AB
1771-CFM Configurable Flowmeter Module AB
1771-CK I/O Chassis Power Cable AB
1771-CP1 I/O Chassis Cable AB
1771-CP2 I/O Chassis Cable AB
1771-CPI I/O Chassis Power Cable AB
1771-CR PLC-2 Processor Cable AB
1771-DA ASCII I/O AB
1771-DB Basic Module AB
1771-DC Real-Time Clock Module AB
1771-DCM 1771-DCM B Direct Communication Module AB
1771-DS Digital Input Module AB
1771-DW Digital Input Module AB
1771-E1C Analog Input Expander AB
1771-ES Servo Encoder Feedback Expander Module AB
1771-HM3A IMC-123 64 KW CMOS Memory Module AB

Amray 91207-1-1 TV Rate Control System PCB 800-2436 used working

Meiden UP004 Battery Module used working

Amray 91219C HI-REL Version PCB 800-2480 used working

Novellus 90-2735 Interlock BD A2000 PCB Revision B Lot of 4 used working

Amray 91161-1-1 Video Control System PCB w/ Sub PCB used working

Daifuku P0D-3716A PCB Kokuasi Vertron used working

Amray 91095 PC10M PCB w/ Sub-PCB 90788D used working

Amray 90792-2-1 Digital Electron Optics Ctrl Assembly PCB 800-1201D used working

Jenoptik 013501-130-17i4 Infab Control Board used working

Copley Contros 800-494 Amplifier used working

Shinko SBX93-100024-11 Circuit Board FLPCN1 SBX08-000013-11 used working

KLA-Tencor 288845 Power Back Plane Motherboard used working

Amray 92102-01-1 High Speed Deflection Power Amplifiers used working

GaSonics 06764002 Arm Controller GaSonics Aura 2000-LL used working

Amray 90952D Programmable Scan Generator PCB 800-1421D used working

Gasonics 90-1036-01 MFC/MFM Interface PCB Revision C Lot of 2 used working

Amray 91024 Gun Control Card PCB 800-1750D Rev. E2 used working

Shinko SBX93-100003-C1 Circuit Board LPCN-1A-I SBX08-000003-11 used working

Amray 90793D PC Card Front Panel Controller 800-1707D PCB used working

Mizar 6800-03417-0001 7300 Serial PCB used working

Mizar 6800-04359-0025 7130 CPU PCB used working

The use of the product:

Moore Automation is a company specializing in the sales of modules and spare parts for world-renowned brands (DCs systems, robot systems, large servo control systems). The company's products include: distributed control systems (DCS), programmable controllers (PLC), MOTOROLA -MVME industrial modules, industrial control communication converters (Anybus), remote output/input modules (RTU), industrial computers (PC), industrial low-frequency screens (IPC), human-machine interface SCSI (50, 68, 80Pin ) AnyBus(Gateway)o The spare parts we sell provide one-year quality guarantee and have undergone strict testing and certification. Now we have become a global sales enterprise of industrial automation spare parts and components.