ABB Module XV371A ABB XV371 A VENTURE DOUBLE PURPLE New spot folding

Product Description:

f the open-circuit or short-circuit monitoring is configured, the detected error is displayed by the red LED Ovl as long as it is present. In the PLC system an error message is stored (FK4, error number 9).
In order to avoid error messages with unused analog inputs, it is useful, not to configure this channels for Pt100. Connection of Pt100 temperature sensors in 3-wire configuration If the sensors are located close together, only one core is needed as
the return wire AGND1. In the operating mode "Pt100 in 3-wire configuration" two adjacent analog inputs belong together (e.g. EW 6,00 and EW 6,01). For configuration, both inputs must be configured to the
desired operating mode, see configuration table Fig. The constant current of the one channel flows through the Pt100 resistance sensor, the constant current of the other channel through one of the wires.
The basic unit 07 KT 94 calculates the measuring value from the two voltage drops and stores it under the odd address

Related Product Recommendation:

Product's Character:

IResolution in the PLC system: The measured values are converted with a resolution of
12 bits, i.e. 11 bits plus sign for voltage and 12 bits without sign for current. The ranges 0...5 V und ±5 V are converted with 10 bits plus sign.the output A 62,00 is only available for the counter. If the output is to use as a normal digital output, it has to Further details can be found in volume 2, chapter 5.1 "General
information for the use of analog inputs and outputs". In order to make sure, that unused input channels have a defined 0V level, they may be shorted to AGND. Unused inputs must be configured with "unused".
The relationship between the analog input signals and the converted numbers is illustrated in the following figures. be made sure, that the high-speed counter is not configured to the operating modes 1 or 2 (see also the chapter "High-speed counter").Features of the analog inputs:The 8 analog inputs are not electrically isolated.The resolution of the A/D converter is 12 bits. Analog signals are conducted in shielded cables (seeThe analog inputs can be configured individually in a lot of different operating modes (even as digital inputs). The configuration is performed by setting certain bits in the system constants KW 86,00 to KW 86,07 as follows

CMA 121 3DDE 300 401 DC Power Supply Module ABB
CMA 122 CPU Card ABB
CMA 123 CMA123 Display Card ABB
CMA 124 Measuring Card ABB
CMA 125 Generator Card ABB
CMA 126 Interface Card ABB
CMA 132 Generator Relay Terminal Board ABB
CMA 133 3DDE 300 413 Terminal board ABB
CMA 136 Generator Relay Terminal Board ABB
CMA 137 Connection Module ABB
CMA131 Servo-motor Drive Encoder Module ABB
CMA135 Diesel Start Stop Automatic Module ABB
CMM11 Condition Monitoring Module ABB
CP501 1SBP260170R1001 Text Display ABB
CP502 1SBP 260171 R1001 Text Display Panel ABB
CP503 1SBP 260172 R1001 Text Display Panel ABB
CP511 1SBP 260173 R1001 Operator Panel - Graphics and Text ABB
CP512 1SBP 260174 R1001 Operator Panel - Graphics and Text ABB
CPU86-NDP 57287586 CPU Processor Board ABB
CS512 3BUR980009R1 CS512 DCN Interface Module ABB
CS513 3BSE000435R1 MasterBus 300E Communications Module ABB
CS513K01 3BSE004772R1 MasterBus 300E Communications Module ABB
CS513K02 3BSE004773R1 MasterBus 300E Communications Module ABB
CS513K04 3BSE055760R1 MasterBus 300/300E Comm. Interface for RJ45 ABB
CSC01 Loop Command Sequence Controller ABB
CT 370a GJR2 237500 R1, GJR2237500R0001 CT 370a Module ABB
CT 5536a HEIE420807R1, HEIE420807R0001 CT5536a Module ABB
CTT01 Configuration Tuning Terminal Bailey
CTT02 Handheld Configurator Tuning Terminal ABB
DAC85-10B 57574825BA ULMA D/A Converter Module ABB

DAI 01 P 37131-4-0369628 DAI01 Analog Input Module ABB
DAI 02 0369630M DAI 02 Analog Input Module ABB
DAI 03 P 37141-4-0369631 Analog Input Module ABB
DAI 04 P37131-4-0369632 Analog Input Module ABB
DAI 05 P 37131-4-0336025 DAI 05 Analog Input Module ABB
DAO 01 P 3717-4-0369629 DAO 01 Analog Output Module ABB

The use of the product:

Moore Automation is a company specializing in the sales of modules and spare parts for world-renowned brands (DCs systems, robot systems, large servo control systems). The company's products include: distributed control systems (DCS), programmable controllers (PLC), MOTOROLA -MVME industrial modules, industrial control communication converters (Anybus), remote output/input modules (RTU), industrial computers (PC), industrial low-frequency screens (IPC), human-machine interface SCSI (50, 68, 80Pin ) AnyBus(Gateway)o The spare parts we sell provide one-year quality guarantee and have undergone strict testing and certification. Now we have become a global sales enterprise of industrial automation spare parts and components.